Match the charger first
The catalogue lists CC–CV 14.6V for 12.8V models and 29.2V for 25.6V models. Confirm the existing charger profile and cut-off logic.
Lead-acid replacement · 1.28–5.12 kWh
Five catalogue configurations for buyers replacing a 12V or 24V lead-acid battery only after checking charger voltage, continuous current, enclosure size and equipment cut-off limits.


Installation planning
A lead-acid replacement requires more than matching the voltage label. Confirm the charger profile, cut-off settings, current demand, terminals and available enclosure space. Include the equipment model and installation drawing with your inquiry.
Product range
The current catalogue comparison covers three 12.8V models at 100Ah, 200Ah and 280Ah, plus two 25.6V models at 100Ah and 200Ah. All use LFP chemistry with a built-in BMS. The listed options differ materially in operating voltage, maximum current, size and weight, so a drop-in decision cannot be based on the nominal voltage or case appearance alone.
Model comparison
These figures are transcribed from the catalogue revision identified with the product image. Request the current model datasheet before approval or purchase.
| Model | Energy | Configuration | Operating range | Rated current | Max. charge / discharge | Size (mm) | Weight |
|---|---|---|---|---|---|---|---|
| CPLI-12.8-100 | 1.28kWh | 4S1P | 10–14.6V | 50A | 50A / 100A | 329 × 174 × 214 | 10kg |
| CPLI-12.8-200 | 2.56kWh | 4S2P | 10–14.6V | 100A | 100A / 200A | 483 × 170 × 240 | 20kg |
| CPLI-12.8-280 | 3.58kWh | 4S1P | 10–14.6V | 140A | 140A / 200A | 522 × 239 × 219 | 25kg |
| CPLI-25.6-100 | 2.56kWh | 8S1P | 20–29.2V | 50A | 50A / 100A | 483 × 170 × 240 | 20kg |
| CPLI-25.6-200 | 5.12kWh | 8S2P | 20–29.2V | 100A | 100A / 200A | 520 × 268 × 221 | 37kg |
Product selection
Available project information is enough for an initial model shortlist and document response.
The catalogue lists CC–CV 14.6V for 12.8V models and 29.2V for 25.6V models. Confirm the existing charger profile and cut-off logic.
A 100Ah label does not prove the battery can start or sustain an inverter, motor, pump or other high-current load.
Compare length, width, height, terminal position, cable clearance and mounting restraint—not only the nominal case class.
Typical applications
Product matching is based on the equipment, duty cycle and installation conditions supplied with the inquiry.
Review weight, peak loads, alternator or shore charger compatibility and enclosure ventilation.
Match controller voltage, daily energy use, autonomy target and recovery after low-sun periods.
Confirm DC operating range, BMS behaviour, recharge time and alarm or communication requirements.
Commercial information
Availability, documents and commercial terms are provided against the requested model, quantity and destination.
For an accurate quote
LiFePO4 product range
Product FAQ
We will confirm current availability, documents and commercial terms for the exact model you select.
No. Confirm charger voltage, low-voltage cut-off, peak current, terminal layout and enclosure fit before replacement.
CPLI-25.6-200 is listed at 5.12kWh. It is not automatically the best fit if the equipment operates on a 12V-class bus.
The catalogue lists optional Bluetooth, LCD, CAN and RS485. Request the current model interface sheet because availability can vary.
The comparison states charge 0–50°C and discharge −10–50°C, with storage at 10–35°C.
The catalogue lists at least 6,000 cycles at stated conditions and IEC 62619, UN38.3, CE and RoHS. Current supporting documents must be checked for the exact model.
Product inquiry
Send the available application, voltage, load, runtime, installation space, quantity and destination.