Battery knowledge · technical procurement

How to Compare Battery Datasheets: A Practical Checklist for Buyers

Put every supplier on the same electrical, environmental, test and delivery boundary before comparing headline values.

Read the fields

Know what each number includes—and leaves out.

Datasheet terms can refer to different boundaries. Confirm whether a value applies to a cell, battery pack, DC cabinet or complete AC system.

01

Nominal voltage

Reference voltage used for identification and energy calculation; not the full operating window.

02

Voltage range

Minimum and maximum operating or cutoff limits, which must match the charger, inverter and protection strategy.

03

Capacity (Ah)

Charge quantity. Ah alone does not establish energy unless voltage and operating conditions are also known.

04

Nominal / usable energy

Nominal Wh or kWh is a reference value; usable energy depends on SOC window, limits, efficiency and system conditions.

05

Continuous / peak current

Current limits must include allowed duration, temperature, SOC and recovery conditions.

06

Power

Electrical rate in W or kW. Confirm whether the value is continuous, peak, DC-side or AC-side.

07

C-rate

Current relative to rated Ah capacity. The same C-rate can represent different amperes on different batteries.

08

SOC / DoD

State of charge and depth of discharge define the operating window used for energy and life claims.

09

Round-trip efficiency

Energy-out versus energy-in across a stated boundary and test condition; cell, battery and AC-system results are not interchangeable.

10

Cycle life

Number of cycles to a stated end-of-life criterion under defined temperature, DoD, current, cutoff and rest conditions.

Screening formulas

Useful for an initial check—not a design guarantee.

Actual usable energy and duration depend on SOC window, efficiency, load, temperature, inverter/PCS limits and system losses.

NOMINAL ENERGYWh ≈ nominal voltage (V) × capacity (Ah)

This estimates nominal DC energy at the stated reference values. It does not establish usable energy.

IDEALIZED DURATIONhours ≈ energy (kWh) ÷ power (kW)

This is a screening relationship. Confirm which energy and power boundary is used and apply system limits and losses.

Test conditions

Do not compare results measured under different rules.

Record temperature, SOC/DoD, current or C-rate, cutoff, rest time, sample basis, test standard and document revision. If they differ materially, ask for aligned evidence rather than choosing the most attractive number.

01

Temperature

Separate charging, discharging and storage. Include soak time, thermal controls and derating.

02

Electrical window

Match SOC/DoD, current, voltage cutoff and peak duration.

03

Product level

Do not extend a cell-sample result to a module, pack or system without product-level evidence.

Copyable buyer checklist

Use one worksheet for every supplier.

Mark unavailable items as Not provided / confirm for the selected product. Keep assumptions outside the supplier data column.

  1. Exact model and document revision/date
  2. Supply level: cell, module, pack, rack or system
  3. Nominal voltage and full operating window
  4. Rated Ah, nominal energy and stated usable energy
  5. Continuous, peak and pulse current with duration
  6. Charge/discharge limits and cutoff conditions
  7. CAN/RS485 or other interface and protocol revision
  8. Dimensions, mass, mounting and connector boundary
  9. Charge, discharge and storage temperature separately
  10. Test conditions, sample basis and applicable standard
  11. Certificate/test-report scope and exact covered model
  12. Warranty terms, exclusions and end-of-life criterion
  13. Included accessories, documents and delivery boundary
  14. Conflicts, missing values and supplier clarifications

Datasheet FAQ

Common reasons comparisons fail.

Does the same Ah rating mean the same energy?

No. Energy also depends on voltage and the usable operating window. Compare Wh or kWh on the same boundary and conditions.

Does the same CAN connector mean two batteries are compatible?

No. Physical connector, pinout, bitrate, message map, protocol version and inverter or host support must all match.

Can cycle-life figures be compared directly across suppliers?

Only when the temperature, SOC/DoD, current or C-rate, cutoff, rest periods and end-of-life criterion are sufficiently aligned.

What should I do when datasheet values conflict?

Record the model, document title, revision and conflicting fields. Ask the supplier to identify the controlling current document in writing before selection.

SCOPE AND SOURCES · REVIEWED 2026-11-14

General sizing and procurement references.

Formulas and checklist items are for buyer screening and scope definition. They are not SES product ratings, engineering design results or performance guarantees.

Send the datasheets and the application boundary.

Include model numbers, revisions, load, voltage, runtime, environment and interface requirements for a technical review.

Request Datasheet Review ↗